Installation is the reverse of removal

“Installation is the reverse of removal” is a familiar phrase to anyone who’s read a Haynes manual. It usually appears at the end of a set of long and complicated instructions about removing something oily and can be translated as: “putting it back on is just as hard and complicated as taking it off. Good luck!”

With the bike back, it’s now time to re-build. So far there haven’t been too many issues.

First up was the bottom bracket and cranks. These went on like a dream, the replacement BB cup and cone fitting perfectly after I’d cleaned up the shell threads. The axle went in, the cranks went on, followed by the pedals; it was pretty much perfect.

I then fitted the headset. The interface between the headset cup races and the frame is snug and this is rather important. Play here will lead to wear on the interface; the very thing the bearings are there to avoid! To fit the races, one typically uses a bearing press such as the Park Tools HHP-2, which retails for £140. Being a cheapskate, I made my own, using:

  • An M8 threaded rod (M8x1000 but M8x250 would do just fine)
  • Two M8 nuts
  • Four M8x50 penny washers
  • Two M8x25 penny washers

Thread the contraption through the head tube and tighten with trusty pair of spanners. I first tried with just the nuts and 50mm penny washers; the force exerted was enough to bend the washers! I suspect the new paint was thicker than the old, which won’t have helped. Using two of them, and spreading the load with a 25mm washer did the trick. Cups inserted!

If I was doing it again, I might be tempted by an M10 (or even M12) setup. M8 worked, but I did put a lot of force through those threads.

With the cups in, I mounted the forks and applied the headset. Lovely. While I was looking at the frame, I needed to check the rear dropouts were aligned; these should both be pointing straight forward. Again, the usual tool for this is a Park Tools FFG-2 which retails for a hundred quid; again, you can make your own. I used:

  • Two M8x200 carriage bolts
  • Two M8x50 penny washers
  • Four wingnuts
  • Four M8x16 (ish) washers
  • Two nuts
  • Two locknuts

Incidentally, the cost for all these tools was under a tenner.

The procedure is: lock the tools in as per the picture; use the leverage of the carriage bolt to line up the penny washers. It’s slightly trickier than with the proper tool, which effectively has two sockets you perfectly match up; but it’s an awful lot cheaper! Mine were pretty good; the photo shows the pre-adjustment alignment. Not too much tweaking at all and I’d have been gutted to spend a hundred pounds.

With the frameset done, brakes were next. I had found a set of brand new 1990s Campagnolo Record dual pivot calipers. Technically, they still have a three year warranty. They’re lovely, although they are significantly heavier than my previous Weinmanns. A new length of outer slipped through the top tube really easily – I’ve heard it can be a nightmare but no dramas here. A couple of new cables and the braking system is done!

The last major system is the drivetrain – read: gearing – and finishing kit. The front mech is on; the rear is on the way. It will need a new hanger, which Keith The Cycle Guy sorted for me when I popped in for some brake cables. Then it’s just a case of fitting the gear levers & cables and tuning the thing. Maybe I should go fixie after all…

Get your cranks off, baby

I had found there is little in this world quite as satisfying as removing a stuck-on crank. It’s like that feeling you get when removing the protective film from a new mobile phone, achieving the gift-wrap-glide or watching a slinky on a treadmill.

Postie brought me presents today. First up was the crank puller. I was reflecting that, depending on what I cranks I put on, I may never user this tool ever again and I probably could have borrowed one – but hey ho, its outline looks good on the tool wall. Pulling a crank is shown very well at https://www.youtube.com/watch?v=64m1mmPFxcc; that bit at 3:00? Ooh….

With the cranks and locknut off, the cups came out easily and with them the axle. As expected, the bearings were properly manky with barely a drop of grease to be seen and plenty of dirt. I now need to decide whether to clean, re-grease and replace the bearings – assuming they’re in good nick (I haven’t had a proper look) or whether to install a modern square taper sealed cartridge BB like those found at https://www.sjscycles.co.uk/square-tapered-other/ Given that a packet of BBs is only half the price of a sealed cartridge I’ll probably opt for the latter.

The second postie present was a set of thread pitch gauges, using which I have confirmed my BB uses 24tpi threads. The last detail is important; old Raleighs often used 26tpi and that would have made sourcing a replacement tricky. Happily I can rest easy! It’s also 68mm and English threaded (lefty-tighty, righty-loosy on the drive side).

For completeness, I also removed the gear cable guide from the underside of the BB and the iconic Raleigh Heron badge from the front. The strip is complete! All I need now before heading to the blasters is to sort out these wretched forks…

Bearings and Bendings

In between other tasks today, I stripped, cleaned and re-greased the bearings on the front wheel (I had done the rear previously). They started mucky, they ended beautifully clean!

All I need now is a tool to remove my cranks and that’s part one done. Tools used: 13mm cone wrench, adjustable spanner (imperial) and a tub of grease.

After a nudge from a friend, I inspected the frame. The forks are quite bent; each blade is bent back and each by a different amount. You can see some bend in the picture below. Not sure what to do about this. I might just deal with it – after all I never really noticed, other than having to be careful when mounting wheels and not turning too sharply lest I foul on my foot. The rear, however…

I used a broom handle to check the frame alignment. You run the handle down next to the head tube and seatpost and inside the rear stays, right down to the dropout. Measure the distance from the handle to the dropout. Repeat both sides; the distance should be the same. It wasn’t; the left side was 15mm away; the right 36mm! A major imbalance. Furthermore, I said previously I didn’t want to cold-set to 130mm spacing at the rear; however, it turns out that someone else got there first.

The gap from centre to each side should be 66mm, having originally been 63mm. A bit of maths tells me it’s now 56mm on the left and 76mm on the right; so not only has the frame been widened, both stays have been pushed to the right.

This leaves me in a quandary. I’m not going to try and cold-set the frame back to 126mm; leaving it as-is gives me loads of options including freewheel-based Campy 7-8 speed or freehub-based 8 speed and up. However, I ought to centre it so that the frame is at least aligned which means moving both stays by 10mm – but then it doesn’t shimmy and I can ride it hands-free so i’m half tempted to leave it.

Wider stays meant I was able to put my (knackered) Fulcrum RQ Carbons in, just for kicks and giggles. Talk about era clash. So wrong it’s right!